Knowing Plumbing Basics is Important For Installing a Bathtub
Knowing Plumbing Basics is Important For Installing a Bathtub
Blog Article
Almost everyone is bound to have their own thinking about Tools You Need to Install a New Bathtub .
Mounting a tub isn't precisely rocket science, but it does require strong plumbing, carpentry, and sometimes, tiling abilities. Changing an old tub with a new one is additionally a moderately challenging job. If the old tub is readily easily accessible, the job can move quickly; if you have to open up a wall surface to get rid of the old tub and place the new tub, the task is a lot harder. In either situation, the job is within a home handyman's abilities, although you will require an assistant to move out the old bathtub and embeded in the new one. See to it you have certified yourself for the work as well as fit attempting it. As opposed to hiring a service provider to take over a halfway-completed project, it is far better to consider utilizing one prior to you start. Chances are you might require a professional plumber to make tube connections.
This post will assist you set up a brand-new bath tub in your bathroom if you have already gotten a brand-new bathtub as well as don't need to alter the plan of your previous water pipes.
Your tools and also product list need to make up the following:
Removing Old Taps
If you require to change old taps with brand-new ones as a part of your installment, after that the first thing you should do is detach the supply of water. After doing so, switch on the faucets to drain pipes any water remaining in the system. The procedure of eliminating the existing faucets can be quite troublesome because of the restricted gain access to that is commonly the case.
Make use of a basin wrench (crowsfoot spanner) or a tap device to undo the nut that links the supply pipes to the faucets. Have a fabric all set for the remaining water that will certainly come from the pipelines. When the supply pipes have actually been removed, use the very same tool to loosen up the nut that holds the taps onto the bath/basin. You will require to stop the single taps from turning during this procedure. As soon as the taps have actually been eliminated, the holes in the bath/basin will have to be cleaned of any type of old sealing compound.
Prior to proceeding to fit the brand-new taps, compare the pipe links on the old faucets to the brand-new taps. If the old faucets are longer than the brand-new taps, then a shank adapter is needed for the brand-new faucets to fit.
Fitting New Taps
If the tails of the brand-new taps are plastic, after that you will certainly require a plastic connector to avoid damages to the thread. One end of the port fits on the plastic tail of the faucet as well as the various other end gives a connection to the existent supply pipelines.
If you need to fit a monobloc, after that you will certainly require lowering couplers, which attaches the 10mm pipe of the monobloc to the common 15mm supply pipeline.
Next off, position the faucet in the installing opening in the bath/basin making certain that the washing machines remain in location between the tap and the sink. Secure the faucet in place with the manufacturer supplied backnut. When the faucet is firmly in position, the supply pipes can be attached to the tails of the faucets. The taps can either be attached by using corrugated copper piping or with regular faucet ports. The previous type should be connected to the tap finishes initially, tightening up only by hand. The supply pipes can later on be linked to the various other end. Tighten both ends with a spanner after both ends have actually been attached.
Setting up the Tub
Making use of the two wooden boards under its feet, place the bathtub in the needed setting. The wood boards are useful in evenly spreading out the weight of the bath tub over the location of the boards as opposed to concentrating all the weight onto four tiny factors.
The following objective is to ensure that the tub is leveled all round. This can be achieved by inspecting the spirit level and adjusting the feet on the bath tub until the level reads degree.
To set up faucets, fit the bottom of the outermost versatile faucet connector to the appropriate supply pipe by making a compression sign up with; then do the exact same for the other faucet.
Activate the water system and check all joints and new pipework for leakages and also tighten them if necessary. Fill up the bathtub and likewise examine the overflow outlet and also the normal electrical outlet for leaks.
Finally, repair the bath paneling as defined in the manufacturer's instruction manual. Tiling and also securing around the bathtub should wait up until the bathtub has been utilized a minimum of when as this will settle it right into its last position.
Preparing for the Setup
Firstly, the supporting framework provided with the bathroom must be fitted (if needed) according to the maker's directions. Next, fit the taps or mixer to the tub. When suitable the faucet block, it is necessary to ensure that if the faucet includes a plastic washing machine, it is fitted in between the bathroom and the faucets. On a plastic bath, it is likewise sensible to fit a sustaining plate under the faucets device to avoid pressure on the bathtub.
Fit the adaptable tap ports to the bottom of the two taps utilizing 2 nuts and also olives (sometimes supplied with the bathtub). Fit the plug-hole outlet by smearing mastic filler round the sink outlet hole, and afterwards pass the outlet via the hole in the bath. Make use of the nut provided by the maker to fit the plug-hole. Take a look at the plug-hole outlet for an inlet on the side for the overflow pipeline.
Next, fit completion of the flexible overflow pipe to the overflow outlet. Afterwards, screw the pipeline to the overflow face which should be fitted inside the bath. Make sure you make use of all of the supplied washers.
Attach the trap to the bottom of the waste outlet on the tub by winding the thread of the waste outlet with silicone mastic or PTFE tape, as well as screw on the catch to the outlet. Attach all-time low of the overflow tube in a similar manner.The bathroom should now prepare to be fitted in its final setting.
Tiling Around the Bathtub
In the area where the bathroom fulfills the floor tile, it is needed to secure the joins with a silicone rubber caulking. This is important as the fitting can move sufficient to fracture a stiff seal, triggering the water to penetrate the wall surface in between the bathroom and also the tiling, leading to difficulties with wetness and also possible leakages to the ceiling below.
You can pick from a variety of coloured sealers to assimilate your components as well as installations. They are offered in tubes and also cartridges, and can securing voids up to a width of 3mm (1/8 inch). If you have a bigger gap to fill up, you can load it with spins of soaked newspaper or soft rope. Keep in mind to always fill up the tub with water prior to sealing, to allow for the movement experienced when the tub is in use. The sealer can fracture fairly very early if you do not take into account this movement before sealing.
Additionally, ceramic coving or quadrant ceramic tiles can be utilized to edge the bathroom or shower tray. Plastic strips of coving, which are easy to use and reduce to dimension, are additionally easily readily available on the market. It is a good idea to fit the ceramic tiles utilizing water-resistant or water-proof sticky as well as grout.
How to Install or Replace a Bathtub
Find Your Dimensions
The first step in any bathtub installation or replacement is to select the right size tub for your bathroom. Start by measuring your existing bathtub’s alcove from wall to wall. The standard size for bathtubs is around 5 feet long and 30 or 32 inches wide. Purchase the size that’s closest to your previous tub.
After you’ve measured, you’ll need to figure out what type of tub you need. Face the alcove. If the drain is on the right-hand side, you’ll need a right drain tub. If it’s on the left, get a left drain tub. Easy enough, right?
Disconnect the Water Supply and Drain Assembly
Before you can start on your removal, make sure that you turn off the tub’s water supply. Some bathrooms have a shutoff valve, but if you don’t see one, you’ll need to turn off the supply at your house’s water main. Once the water’s off, open the valves to release any remaining air in the supply lines.
Then, disconnect the tub drain flange. This process varies based on the type of drain you have, but in most cases, you’ll need a drain flange removal tool to perform this task. If you’re feeling handy, you might be able to use a pair of needle-nose pliers to twist and pull the flange.
Now comes the fun part. In order to disconnect the drain assembly, you’ll need to be able to get to the space underneath the tub. You might need to access the tub drain from a crawlspace or a basement. Don’t forget to take a pipe wrench with you, as you’ll need it to loosen the pipe at the connection.
Cut Out the Old Tub
After removing the drainpipe assembly, you can take out the old bathtub. Cut a strip above the tub edge in the wall surrounding the bathtub that's about 6 inches in height. The tools you need here may vary depending on the type of wall surround you have in the alcove. If you’re cutting drywall, use a drywall saw and remove the section of the wall all the way down to the studs. If you have tile, you’ll need to use a grinder with a diamond blade to cut through the grout line. Then, use a chisel to remove the individual tiles. Take care here not to cut through any studs.
Find the tub flange. Remove the screws that attach the flange to the studs in the wall. At this point, the tub should be freed from the wall.
Once you’ve removed the flange, use a utility knife to cut away the caulk between the tub and the floor. When this is done, you should be able to lift the tub up and out of the alcove. Keep in mind that, depending on what it’s made of, the old tub could be tremendously heavy. You should plan to have a friend help you move it just in case.
Install the New Tub
Before you make any adjustments to the area, place the new tub in the alcove to make sure it fits properly and that the tub drain lines up with the P-trap underneath the floor.
Remove it and install a 2 x 4 ledger board. Measure the tub’s flange, then mark that height on the wall. Screw the ledger board to studs in the wall. This will help to support the weight of the tub.
Once the ledger board has been installed, go ahead and secure the drain to the tub. For this step, you’ll need some plumber’s putty. Roll a small amount of putty in your hands and wrap it around the underside of the drain flange. Push the drain into the tub from underneath the tub.
When the drain has been attached, connect the overflow drain. To do this, you’ll place the gasket on the overflow elbow and move it behind the tub. Once that’s on, connect the overflow pipe and the drainpipe, but take care not to overtighten.
Secure the Tub
After the connections are in, it’s time to set the tub in place. Before you start, make sure the flange lines up with the markings you made in Step 4. Because the ledger board holds the tub in place, it’s important that it matches up. If not, you’ll need to remove it and readjust.
Once your measurements line up, attach the flange to the studs on all three sides of the wall. Please note that you should not screw the flange to the wall. Instead, you should use roofing nails because they won’t rust over time. When the tub is in place, install the baseboard and the molding in front of and around the tub.
Repair and finish off the drywall or tile that you cut in Step 3. If you’re installing a fiberglass bath surround, now’s the time to adhere it to the alcove.
Then, enjoy your tub! While all these steps might seem intimidating, removing and installing a new bathtub is a relatively easy DIY project that can be completed in a single day. And now, when you settle in for your next bubbly soak, you can enjoy your bath without the distraction of a tub in disrepair.
https://www.homeserve.com/en-us/blog/how-to/bathtub-replacement/
I am very drawn to How to Install a Bathtub Yourself and I really hope you enjoyed my entry. I beg you take the opportunity to distribute this content if you enjoyed it. Thanks for taking the time to read it.
Results guaranteed, contact! Report this page